Use a plain belt while the product stays on the belt by friction alone, and a cleated belt once the product starts to slide back. The deciding factors are the angle of the incline, how sticky the product is, and whether it is loaded steadily or in batches.
What an incline conveyor does in the line
An incline conveyor lifts product from a low loading point to the inlet of the next machine. That machine may be a vibrating screen, a washer or a packing machine. The conveyor has no sorting role. Its job is to deliver product at a steady rate, at the right height, without damaging it.
Because it sits between two machines, its discharge decides how the next machine behaves. A stream that arrives in lumps overloads one part of a screen deck. A stream that arrives evenly lets the deck work with a thin, uniform layer.
The plain belt
The inclined belt conveyor carries product on a food-grade PVC or PU belt. The frame is AISI 304 stainless steel with support legs, and a geared motor drives the belt from the head end. Product is loaded at the low end, by hand or through a feed hopper, carried up the incline at a steady speed and dropped into the next machine's inlet.
A plain belt has a smooth carrying surface. It is easy to wipe down and gentle on fragile pieces, and nothing on the belt can trap product. Its limit is the angle. As the incline gets steeper, round and smooth pieces begin to roll back down the belt, and the steady stream turns into a surge.
The cleated belt
Cleats are raised ribs across the belt. They hold product in portions so it cannot slide back, which allows a steeper incline in the same floor space. The cleated incline conveyor uses a PVC cleated belt with a wide hopper at the low end that takes product emptied in batches. Its frame, trough and product contact surfaces are AISI 304 stainless steel. The listed products are raisins, dried apricots, dried figs and dates.
The plain belt page also points to the cleated belt as the option for steeper angles, so the two machines are meant to be read as a pair: the same function, with the cleats added where the angle requires them.
Choosing between them
Work through these questions in order.
- How high must the product go, and how much floor is available? A long, shallow incline suits a plain belt. If the floor space is short and the lift is high, the angle rises and cleats become necessary.
- How does the product behave on a slope? Dry, rounded pieces roll. Soft, sticky pieces cling to the belt and tend to stay put. Mixed lots of dried fruit can do both within one season, so judge the worst case rather than the average.
- How is the product loaded? A person emptying sacks creates batches. A wide hopper smooths that out, and cleats then pass the product up in measured portions. Steady loading from a feeder suits a plain belt better.
- What follows the conveyor? If the next machine is a screen, an even stream matters more than raw lifting power. Cleats deliver in portions, which is fine for a hopper or a washer, but check how the portions land on a screen deck.
Cleaning and hygiene
Cleats add surface. Each cleat forms a corner where the belt meets the rib, and sugary residue collects there first. A plain belt can be wiped in one pass; a cleated belt needs a second look at every cleat base. Both belts are food-grade PVC or PU, and the stainless frame takes hot water and food-safe detergents. Plan the cleaning routine around the belt you choose, not after the fact.
Belt speed and control
Both conveyors list belt speed as adjustable to the product, with a geared motor and PLC or stand-alone control. A frequency inverter for speed control is listed as an option on the plain belt, and speed control is listed as an option on the cleated one. Speed is the simplest way to match the conveyor to the next machine: slow enough that the screen or washer is never flooded, fast enough that the loading point never backs up.
Capacity for both machines is set per project, and dimensions are made to suit the installation. The incline and the discharge height are set to the next machine, so the first step in any enquiry is the position of that machine's inlet relative to the loading point.
A short checklist before choosing
- Inlet height of the next machine and the floor length available.
- Worst-case product: dry and rolling, or soft and sticky.
- Loading method: batch from sacks or steady from a feeder.
- Whether a hopper is needed at the low end.
- How the cleaning will be done at each product changeover.
Answering these in advance narrows the choice to one belt type before any drawing is made.
